Azek Bench Planter Instrukcja Użytkownika Pobierz pdf

Tools Required

Bench Hardware

• Each AZEK Bench and Planter Kit comes complete with all hardware, fasteners and installa-

tion guide to build one complete unit (i.e. AZEK Deck Boards must be purchased separately).

Check the enclosed Hardware and Parts List to ensure that each kit is complete.

• The AZEK Bench and Planter Kits are two separate products that can be used together to build

a “straight bench” (i.e. 2 planters and 1 bench) or a “corner bench” (i.e. 3 planters and 2 benches).

• Both the AZEK Bench and Planter Kits should be installed in accordance with the installation

guidelines included below. AZEK Building Products Inc. accepts no liability or responsibility

for the improper installation of this product.

• The AZEK Bench and Planter Kits are designed to be used with AZEK Deck boards which

measure 1” Thick x 5.5” Wide. AZEK Planter is designed to be built to the size for which it

is manufactured and should not be altered in any way. AZEK Bench is 6FT at full length or

adjustable down to 4 FT. A fully assembled “straight bench” can hold up to 750 LBS.

• AZEK Bench and Planter Kits may not be suitable for every application and it is the sole

Drill &

Drive Tool

Miter/Chop Saw 1/4 Drill BitTable Saw

3/8” Wrench

7/16” Wrench

#2 Phillips

Drive Bit

#3 Phillips

Drive Bit

Planter Parts

Bench Parts

(2) End Cap

(4) Corner Brace

(2)

Bench Corner Bead Support

Please read all instructions completely before starting any part of the installation.

responsibility of the installer to be sure that each Kit is used for its intended purpose.

Since all installations are unique, it is also the installer’s responsibility to determine specic

requirements in regards to each AZEK Bench or Planter application.

• AZEK Building Products recommends that all applications be reviewed by a licensed archi-

tect, engineer, or local building ofcial before installation. Check local code requirements

prior to installation. If you have any questions or need further assistance, please call AZEK

Customer Service at 877-ASK-AZEK (877-275-2935) or visit our website at www.azek.com.

• IMPORTANT: Make sure the DRIVE TOOL/DRILL is congured or set to use the SCREW

setting when driving and/or tightening all FASTENERS. Since most screws are designed

to seat within the cellular PVC substrate, BE VERY CAREFUL NOT TO OVER DRIVE, as this

may loosen the screw’s holding power.

• SAFETY: Always wear goggles when handling, cutting, drilling and fastening materials.

• WARNING: Bench cannot hold more than 750 LBS.

(2) Bench Hanger

Bracket

(4) Top Corner

Bracket

(4) Middle Corner

Casting

(8) Bottom Middle

Corner Bracket

(4) Bottom

Corner Casting

(4) Horizontal Top

Corner Casting

(1) Planter Tub

(4) Top

Corner Casting

(8) Panel Support

(4) Planter Corner

Bead Support

(8) Angle

Bracket

(1) Vent (1) Plug

(28) #10

Flat Washers

(28) #10 Split

Lock Washers

(28) 10-32

Hex. Nuts

(28) #10-32 x

”

Flat Head Phillips

Machine Screws

(62) #8 x

”

Pan Head Phillips

Wood Screws

Planter Hardware

(4) 1/4-20 Regular

Flat Washers

(4) 1/4-20

Split

Lock Washers

(4) 1/4-20

Hex. Nuts

(180) #10 x

”

Flat Head Phillips

Wood Screws

(4)

-20 x 1

”

Hex. Head

Machine Screws

(32) #10 x 1

”

Flat Head Phillips

Wood Screws

BENCH/PLANTER INSTALLATION GUIDELINES for

Arbor Collection

‰

/ Harvest Collection / Terra Collection

‰

Page 1

1 2 3 4 5 6 7 8 9 10

Podsumowanie treści

Strona 1 - Planter Hardware

Tools RequiredBench Hardware• Each AZEK Bench and Planter Kit comes complete with all hardware, fasteners and installa-tion guide to build one complet

Strona 2 - Assemble Corner Brace

Strona 3 - Use Deck Boards from Cut List

Cut corner bead (x2) from one end as shown for 4’ or 5’ bench12Assemble End Caps & Center BracketAssemble Corner Brace#10 Flat Washer (x16) #10 Sp

Strona 4 - Assemble Bottom Frame

Adjust spacing approx. 1/32”453Assemble AZEK Deck BoardsAssemble AZEK Deck BoardsUse Deck Boards from Cut ListSee Table at Right19”Step 3See Table at

Strona 5 - Assemble Planter Sides (x4)

Screws fastened from smooth side of deck board.Assemble Bottom FrameAssemble Planter Sides (x4 Per Planter)26”Step 8#10 3/4” Flat HeadPhillips Wood S

Strona 6 - Assemble Middle Frame

Assemble Planter Corner Beads (x4)Assemble Planter Sides (x4)Position with Small Hole DownCorner BeadsBottom Frame3Planter4Planter#10 x 3/4” Flat Head

Strona 7 - Assemble Top Frame

Assemble Middle FrameAssemble Middle Frame onto Planter26 7/16”45°24 3/4” MIN.Step 1126 7/16”45°24 3/4” MIN.Step 11Cut Deck Board (x4 Per Plante

Strona 8 - Assemble Bench and Planters

abcdPrepare to Assemble Top Frame7Planter8Planter31”45°29”45°227 1/4” MIN.Step 1431”45°29”45°227 1/4” MIN.Step 1431”45°29”45°227 1/4” MIN.Step 1431”45

Strona 9 - 1/4” - 1/2” Strong

Assemble Bench Hanger Brackets (x2 Per Planter) Then Assemble Planter Tub and Top FrameAssemble Bench and Planters2 People Required#10 3/4” Flat Head

Strona 10 - www.AZEK.com

Bench BoardsPlanter SidesMiddle TrimBottom TrimTop TrimTop Frame5 1/2”3 3/8”2”5 1/2”31”29”26 7/ 16”26 7/ 16”26” 19” 19” 72” 72” 12 foot 16 foot 12 fo

Komentarze do niniejszej Instrukcji

Brak uwag

Azek Bench Planter Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Dla domu Azek Bench Planter. AZEK Bench Planter User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Dla domu Azek Bench Planter